ADDI-DATA APCI-7300-3 User Manual

ADDI-DATA GmbH · Airpark Business Center · Airport Boulevard B210 · 77836 Rheinmünster · GermanyPhone +49 7229 1847-0 · Telefax +49 7229 1847-200

APCI-7xxx-3 Figures and Tables Figures Fig. 3-1: Correct handling...12 Fig. 4-1

APCI-7xxx-3 Figures and Tables 7 Fig. 8-2: Connection of the shorting plug RS422... 53 Fig. 8-3: Connection of th

APCI-7xxx-3 Figures and Tables 1 DEFINITION OF APPLICATION 1.1 Intended use The board APCI-7xxx-31 must be inserted in a PC with PCI 5V/32 bit (PCI

APCI-7xxx-3 Figures and Tables The board is to be connected to the peripheral through a shielded cable, which shielding should be grounded on both en

APCI-7xxx-3 Figures and Tables Uses beyond these specifications are not allowed. The manufacturer is not liable for any damages which would result fr

APCI-7xxx-3 Figures and Tables 2 USER 2.1 Qualification Only persons trained in electronics are entitled to perform the following works: - instal

APCI-7xxx-3 Figures and Tables 3 HANDLING OF THE BOARD Fig. 3-1: Correct handling 12

APCI-7xxx-3 Figures and Tables 4 TECHNICAL DATA 4.1 Electromagnetic compatibility (EMC) The board APCI-7xxx-3 complies with the European EMC direct

APCI-7xxx-3 Figures and Tables The board APCI-7800-3 is assembled on a 6-layer circuit. Dimensions: 175 mm 99 mm Weight: ...

APCI-7xxx-3 Figures and Tables 4.3 Limit values Max. altitude: ... 2000 m Operating temperature: ...

www.addi-data.comPlease observe that during the migration to RoHS-compliant boards, the pin assignment of RS232 changed. Thus, there are differences b

APCI-7xxx-3 Figures and Tables 4.3.1 RS232 CCITT-recommendation: ... V.24 US-Norm EIA: ...

APCI-7xxx-3 Figures and Tables 4.3.3 20mA constant current loop (MXTTY) Max. Baud rate:...19.2 kBaud Transorb

APCI-7xxx-3 Figures and Tables 4.4 Component scheme and block diagrams Fig. 4-1: Component scheme of the APCI-7300-3, APCI-7420-3 and APCI-7500-3

APCI-7xxx-3 Figures and Tables Fig. 4-2: Component scheme of the APCI-7800-3 19

APCI-7xxx-3 Figures and Tables Fig. 4-3: Component scheme of the APCI-7800-3 (solder side) 20

APCI-7xxx-3 Figures and Tables Fig. 4-4: Block diagram of the APCI-7300-3 Fig. 4-5: Block diagram of the APCI-7420-3 21

APCI-7xxx-3 Figures and Tables Fig. 4-6: Block diagram of the APCI-7500-3 Fig. 4-7: Block diagram of the APCI-7500-3/4C 22

APCI-7xxx-3 Figures and Tables Fig. 4-8: Block diagram of the APCI-7800-3 23

APCI-7xxx-3 Figures and Tables 5 INSTALLATION OF THE BOARD The interrupt lines and base address of the board are allocated by the BIOS of the PC s

APCI-7xxx-3 Figures and Tables 5.3 Plugging the board into the slot ♦ Insert the board vertically into the chosen slot. Fig. 5-2: Inserting the boa

www.addi-data.comAPCI-7500-3: 37-pin SUB-D-connector37-pin SUB-D connector pin assignment with changed modem control signals DCD & DSR.APCI-7500-3

APCI-7xxx-3 Figures and Tables 6 BOARD CONFIGURATION In this chapter you will find a description of the delivered software and its possible applicat

APCI-7xxx-3 Figures and Tables Fig. 6-1: FIFO settings under Windows 2000∗ PCI bus and device number Management of the transmitter and receiver bu

APCI-7xxx-3 Figures and Tables Under "Setting" you adapt the operating mode to the used interface. Fig. 6-2: Setting example: RS485∗ RS

APCI-7xxx-3 Figures and Tables Fig. 6-3: Setting example: MXTTY current loop: Module configuration∗ Current flows (send): Definition of the current

APCI-7xxx-3 Figures and Tables Fig. 6-4: Setting example: MXTTY current loop: Input clock∗ Input clock: Under ”Crystal frequency“ the frequency of th

APCI-7xxx-3 Figures and Tables 6.3 Questions and software downloads on the web Do not hesitate to e-mail us your questions. per e-mail: info@addi-

APCI-7xxx-3 Figures and Tables 7 CONNECTING THE PERIPHERAL i IMPORTANT! The connector pin assignments are valid for the boards APCI-7300-3, APCI-74

APCI-7xxx-3 Figures and Tables Table 7-1: Pin assignment of the 37-pin connector RS485 RS422 Current Loop RS232 Pin PinRS232 Current Loop RS422 RS

APCI-7xxx-3 Figures and Tables Table 7-2: Pin assignment of the 9-pin connector RS485 RS422 Current Loop RS232 Pin Pin RS232 Current Loop RS422 RS4

APCI-7xxx-3 Figures and Tables Table 7-3: Pin assignment of port 1 Pin RS 232 RS 422 RS 485 RS422PEP Current Loop 20 TxD RA Tx / Rx + Rx+ +

ADDI-DATA GmbH · Airpark Business Center · Airport Boulevard B210 · 77836 Rheinmünster · GermanyPhone +49 7229 1847-0 · Telefax +49 7229 1847-200

APCI-7xxx-3 Figures and Tables Table 7-5: Pin assignment of port 3 Pin RS 232 RS 422 RS 485 RS422PEP Current Loop 14 TxD RA Tx / Rx + Rx+ +

APCI-7xxx-3 Figures and Tables Table 7-7: Pin assignment of port 5 Pin RS 232 RS 422 RS 485 RS422PEP Current Loop 9 TxD RA Tx / Rx + Rx+ +R

APCI-7xxx-3 Figures and Tables Table 7-9: Pin assignment of port 7 Pin RS 232 RS 422 RS 485 RS422PEP Current Loop 4 TxD RA Tx / Rx + Rx+ +R

APCI-7xxx-3 Figures and Tables 7.4 Pin assignments (APCI-7500-3): RS422 with handshake signals With the module MX422-PEP you can use the modem contr

APCI-7xxx-3 Figures and Tables 7.6 Connection cable – APCI-7500-3 Fig. 7-4: Connection cable ST074 (4 x 25-pin) * 1 Resistor integrated on the MX m

APCI-7xxx-3 Figures and Tables 7.7 Connection examples 7.7.1 APCI-7500-3 RS232 cabling Fig. 7-6: RS232 cabling - 4-port interface 1 If the modem c

APCI-7xxx-3 Figures and Tables RS485 cabling Fig. 7-8: RS485 cabling - 4-port interface Current loop (20 mA) cabling Active/passive: When a transmi

APCI-7xxx-3 Figures and Tables Fig. 7-10: Active transmission/passive reception 4-port serial interface Fig. 7-11: Passive transmission/active rece

APCI-7xxx-3 Figures and Tables Fig. 7-12: Passive transmission/passive reception 4-port serial interface 7.7.2 APCI-7300-3, APCI-7420-3, APCI-7500

APCI-7xxx-3 Figures and Tables RS422 cabling Fig. 7-14: RS422 cabling - 9-pin connector RS485 cabling Fig. 7-15: RS485 cabling - 9-pin connector

DIN EN ISO 9001:2000 certified ADDI-DATA GmbHAirpark Business CenterAirport Boulevard B21077836 RheinmünsterGermany+49 7229 1847-0

APCI-7xxx-3 Figures and Tables Current loop (20 mA) cabling Fig. 7-16: Active transmission/active reception 9-pin connector Fig. 7-17: Active trans

APCI-7xxx-3 Figures and Tables Fig. 7-18: Passive transmission/active reception 9-pin connector Fig. 7-19: Passive transmission/passive reception 9

APCI-7xxx-3 Figures and Tables 7.7.3 APCI-7800-3 Fig. 7-20: Connection cable ST7809 (8 x 9 pin) 48

APCI-7xxx-3 Figures and Tables Fig. 7-21: Connection cable ST7825 (8 x 25 pin) 7.8 Connection examples 7.8.1 RS232 cabling Fig. 7-22: RS232 cablin

APCI-7xxx-3 Figures and Tables 1: If the modem control signals are not used, they must be bridged via a wire bridge. 7.8.2 RS422 cabling Fig. 7-23:

APCI-7xxx-3 Figures and Tables 7.8.4 Current Loop (20 mA) cabling Active/passive: When a transmitter and a receiver communicate, one of them has to

APCI-7xxx-3 Figures and Tables Fig. 7-27: Active transmission/passive reception – 4-fold interface Fig. 7-28: Passive transmission/passive receptio

APCI-7xxx-3 Figures and Tables 8 TESTING THE BOARD 8.1 Connecting a shorting plug When using the shorting plug described below and the test program

APCI-7xxx-3 Figures and Tables Fig. 8-3: Connection of the shorting plug for 20 mA Current Loop – active transmission/passive reception Fig. 8-4:

APCI-7xxx-3 Figures and Tables 8.2 Testing the board with the MTTTY program RS422, RS232 and 20 mA Current Loop ♦ Install the program on your PC. T

Product information This manual contains the technical installation and important instructions for correct commissioning and usage, as well as produ

APCI-7xxx-3 Figures and Tables Your settings will be displayed in the lower part of the main menu of the MTTY-program (see figure above) under „Comm

APCI-7xxx-3 Figures and Tables Below on the right of the main window of the MTTTY-program there is a text field for error or status messages. RS485

APCI-7xxx-3 Figures and Tables 9 REPLACING THE MODULES i IMPORTANT! We advise you to send us the board if a module is to be replaced. If you wish

APCI-7xxx-3 Figures and Tables Fig. 9-2: Inserting the MX module 59

APCI-7xxx-3 Figures and Tables 10 GLOSSARY Table 10-1: Glossary Term Description A/D converter = ADC An electronic device that produces a digital

APCI-7xxx-3 Figures and Tables Noise suppression The suppression of undesirable electrical interferences to a signal. Sources of noise include the a

APCI-7xxx-3 Figures and Tables concerning clamp voltage is zero. Short circuit current Short circuit current is the current between tow short-circui

APCI-7xxx-3 Figures and Tables 11 INDEX B Block diagrams 21 Board configuration 26 Board test 30 C Component scheme APCI-7300, APCI-7420-3, APCI-

WARNING The following risks result from improper implementation and from use of the board contrary to the regulations: ♦ Personal injury ♦ Damag

Contents APCI-7xxx-3 1 DEFINITION OF APPLICATION ... 8 1.1 Intended use ....

Contents APCI-7xxx-3 5 7.5 Pin assignments (APCI-7420-3 and APCI-7300-3): RS422 with handshake signals ............